Forside » Dele & tilbehør» Motor & dele» Ventiltræk » Knastakselsæt RS 487 ST, kædetræk, oliekølet, M8 17-
CAM KIT RS 487 ST CHAIN DRIVE OIL COOLED M8 17-

Knastaksel · Feuling

Knastakselsæt RS 487 ST, kædetræk, oliekølet, M8 17-

Varenr. FEULING-7272ST

19.549,00 kr inkl. moms
Skaffevare · leveringstid 5-6 hverdage

Passer til 123 køretøjer

  • Harley Davidson FLDE 1750 ABS 2018Type ST1 ; ST1-R · ja
  • Harley Davidson FLDE 1750 ABS 2019Type ST1 ; ST1-R · ja
  • Harley Davidson FLDE 1750 ABS 2020Type ST1 ; ST1-R · ja
  • Harley Davidson FLFB 1750 ABS 2018Type ST1 ; ST1-R · ja
  • + 119 flere

Fitment-tjekket: passer delen ikke som angivet, tager vi den retur. Vælg din motorcykel i garagen for at se, om den passer til din.

Race Series® Camchest Kit with Short Travel Lifters Kit Includes: • 487 Reaper Camshaft • HP+ Pushrods • Race Series® Short Travel Lifters • High Flow Camplate • Race Series® Oil Pump • Cam Installation Kit • ARP… Læs mere

Beskrivelse fra leverandøren (engelsk)

Race Series® Camchest Kit with Short Travel Lifters

Kit Includes:

• 487 Reaper Camshaft

• HP+ Pushrods

• Race Series® Short Travel Lifters

• High Flow Camplate

• Race Series® Oil Pump

• Cam Installation Kit

• ARP Rocker Studs and Nuts

• Camplate/Oil Pump Fasteners

  • 487 Reaper® Chain Drive Camshaft, Cam Installation Kit, Race Series® Short Travel Lifters, One Piece Pushrod, Race Series® Oil Pump, High Flow Camplate, and ARP Rocker Studs and Nuts, Camplate/Oil Pump Fasteners are included in this kit
  • 487 Reaper Camshaft
  • Chain Drive
  • RPM range 2,250 - 6,100
  • Engineered specifically as a bolt-in camshaft upgrade for factory 114" and 117" M8 engines
  • Responds very well to increased bore and or compression
  • Maintains bottom end power and pulls hard above 2,950 rpm when compared to stock
  • Cam specs measured in the engine on the lifter @ 0.050 using a 1.61 rocker arm ratio.
  • Cam Installation Kit
  • Includes cam bearing, cam/crank hardware and gasket/O-ring kit
  • Race Series® Short Travel Lifters
  • Hydraulic lifters made from machined steel designed with 0.115" of travel
  • One Piece Pushrods
  • HP+ 0.165 wall thickness, +0.040, one piece
  • Race Series® Oil Pump
  • High flow 2.250 Chrome Moly gerotor gears
  • 27% more pressure and scavenge gear volume over stock
  • 42% more scavenge volume with matched passages, port sizing and holes to the engine case
  • 46% more oil volume to the crankshaft and connecting rod bearing
  • 15°- 25° cooler engine temperatures
  • 15°- 30° cooler oil temperatures
  • 10-30 more PSI of oil pressure
  • Reduces wet sumping, blow by and oily air cleaners
  • Magnets in oil pump to help protect gears and pressure relief valve
  • FEULING® test results show a 50% reduction of engine sump oil level.
  • High Flow Camplate
  • Rear wheel power gains of 2 horsepower and 2 ft lb of torque can be achieved
  • Made in the USA
  • Feuling does not recommend tuning beyond stock emissions standards.
  • To install this kit on a stock 107" engine, you cannot use the included one-piece pushrods. You must purchase a separate set of Adjustable Pushrods to manually set the correct lifter preload for your 107" motor. Using the included one-piece pushrods on a 107" engine will cause catastrophic valvetrain damage.